DOC

AISI 1010 Cold Drawn Bar - Saber Steel Group

By Harry Green,2014-03-19 03:00
11 views 0
AISI 1010 Cold Drawn Bar - Saber Steel GroupAisi,AISI,steel,Steel,Cold,Drawn,Bar,Group,cold,aisi

    AISI 1010 Cold Drawn BarM-72431. General Statements

    1.1 Introduction

    AISI 1010 Cold Drawn Bar

    2. Allowable Equivalents

    The following equivalent materials may be used to fulfill this Specification. One or more of the

    following methods may be used to specify materials, but do not duplicate information between

    methods.

    2.1 Existing industry specifications:

    Governing Body (ASTM, JIS, Specification Number

    etc.)Equivalent Material 1010AISI1

    Equivalent Material G3507 SWRCH10AJIS2

    KSD3592 SWRCH10A

    2.2 Existing vendor specific (proprietary):

    Material SupplierSupplier Specification NumberEquivalent Material

    1

    3. Physical Composition

    3.1 Elemental Composition (including tolerance):Element (Copper, aluminum, etc.)Percentage requirement (with tolerance)

    C0.08 – 0.13%

    Mn0.3 – 0.6%

    PMAX 0.04%

    SMAX 0.05%

    AISI 1075M-7080

1. General Statements

    1.1 Introduction

    Steel with good wear characteristics

    2. Allowable Equivalents

    2.1 Existing industry specifications that may be used to fulfill this Material Specification are:

    Governing Body (ASTM, JIS, etc.)Specification Number

    2.2 Existing vendor specific (proprietary) specifications that may be used to fulfill this Material Specification. NOTE! Use of single-source materials should be avoided whenever possible, and only used when no other materials are known that will satisfy the product requirements (DELETE THIS NOTE

    FROM ACTUAL SPECIFICATIONS).

    Material SupplierSupplier Specification Number

    3. Material Composition

    3.1 Elemental Composition

    Specific chemical composition requirements for the material, including tolerance. If none are specified, the

    requirements listed in Section 2 above apply.

    Element (e.g. Copper, aluminum, etc.)Percentage requirement (with tolerance)

    3.2 Physical Composition

    Other physical characteristics not defined above, such as internal dimensional requirements:

    1.AISI 1075 (SK-5, SK 5M)

    2.Must be free of burrs and oil

    Carbon Steel (SWRH72A) M-7181

1. General Statements

    1.1 Introduction

    China SWRH72A Steel

    2. Allowable Equivalents

    The following equivalent materials may be used to fulfill this Specification. One or more of the

    following methods may be used to specify materials, but do not duplicate information between

    methods.

    2.1 Existing industry specifications:

    Governing Body (ASTM, JIS, Specification Number

    etc.)Equivalent Material China Industry Standard SWRH72A1(SWRH)

    Equivalent Material J178SAE2

    Equivalent Material

    3

    2.2 Existing vendor specific (proprietary):

    Material SupplierSupplier Specification NumberEquivalent Material

    1

    Equivalent Material

    2

    Equivalent Material

    3

    3. Physical Composition

    3.1 Elemental Composition (including tolerance):Element (Copper, aluminum, etc.)Percentage requirement (with tolerance)

    0.72 maxC%

    Si%0.19 max

    Mn%0.48 max

    S%0.009 max

    P%0.011 max

    Carbon Steel specification M-7030

1. General Statements

    1.1 Introduction

    Carbon Steel and optional material for Retainers, Covers, CE Frames, Shields, Frames,

    Shunts and laminations used on PG260G, N, NS, P motors..

    2. Allowable Equivalents

    The following equivalent materials may be used to fulfill this Specification. One or more of the

    following methods may be used to specify materials, but do not duplicate information between

    methods.

    2.1 Existing industry specifications:

    Governing Body (ASTM, JIS, Specification Number

    etc.)Equivalent Material AISI10081

    Equivalent Material EN10130DC01 or DC041

    Equivalent Material JISSPCD1

    Equivalent Material KSSCP21

    2.2 Existing vendor specific (proprietary):

    Material SupplierSupplier Specification Number

    Equivalent Material

    1

    Equivalent Material

    2

    Equivalent Material

    3

    Carbon Steels for Machine Structural Use M-7177

1. General Statements

    1.1 Introduction

    This Specification specifies carbon steels for machine structural use manufactured by hot forming,

    such as hot rolling or hot forging, ordinarily to be used after further process of forging, cutting and

    heat treatment, hereinafter referred to as the “steel”

    2. Allowable Equivalents

    2.1 Existing industry specifications that may be used to fulfill this Material Specification are:

    Governing BodySpecification Number

    JISS20C

    KSSM20C

    UNS10200

    AISI / SAE1020

     EN (DIN)C22/ C22E/ C22R

    2.2 Existing vendor specific (proprietary) specifications that may be used to fulfill this Material Specification.

    Material ProviderSpecification Number

    3. Material Composition

    3.1 Elemental Composition

    Specific chemical composition requirements for the material, including tolerance.

     If none are specified, the requirements listed in Section 2 above apply.

    C0.18 ~ 0.23 %

    Si0.15~ 0.35%

    Mn0.30 ~ 0.60 %

    P0.030 Max %

    0.035 Max %S

    3.2 Physical Composition

    1. General Statements M-7096

1.1 Introduction

    Hard copper

    2. Allowable Equivalents

    2.1 Existing industry specifications that may be used to fulfill this Material Specification are:

    Governing Body (ASTM, JIS, etc.)Specification Number

    UNSC 11000 H08 ETP

    SAEJ461/J463 C11000

    JISH3260 C 1100 W-H

    KSD5103 C 1100 W-H

    EN1652 CU-ETP CW004A H1103. Material Composition

    3.1 Elemental Composition

    Specific chemical composition requirements for the material, including tolerance. If none are specified, the

    requirements listed in Section 2 above apply.Chemical Composition

    Cu 99.90% MIN

    3.2 Physical Composition

    Other physical characteristics not defined above, including dimensional requirements:2Tensile Strength : 285 N/mm MIN

    4. Performance and Durability Tests4.1 Performance Tests

    TestProcedureRequirement

    4.2 Durability Tests

    TestProcedureRequirement

    5. Other requirements

    5.1 Other requirements

    List any requirements for the material composition, performance, appearance, packaging, etc. not

    listed above:

    Electrical Resistivity: Max 17.3 mOhm-m2 (@20?C)

    O(oxygen) chemical composition : 0.01% MIN (100PPM MIN)

M7036

    Carbon Steel Tube

    1. General Statements

    1.1 Introduction

    Carbon Steel Tubes for Machine Structural Purposes

    2. Allowable Equivalents

    2.1 Existing industry specifications that may be used to fulfill this Material Specification are:

    Governing Body (ASTM, JIS, etc.)Specification Number

    JIS G3445 STKM 11A

    2.2 Existing vendor specific (proprietary) specifications that may be used to fulfill this Material Specification. NOTE! Use of single-source materials should be avoided whenever possible, and only

    used when no other materials are known that will satisfy the product requirements (DELETE THIS NOTE

    FROM ACTUAL SPECIFICATIONS).

    Material SupplierSupplier Specification Number

    3. Material Composition

    3.1 Elemental Composition

    Specific chemical composition requirements for the material, including tolerance. If none are specified, the

    requirements listed in Section 2 above apply.

    Element (e.g. Copper, aluminum, etc.)Percentage requirement (with tolerance)C 0.12 max

    Si 0.35 max

    Mn 0.60 max

    P 0.040 max

    S 0.040 max

    3.2 Physical Composition

    Other physical characteristics not defined above, such as internal dimensional requirements:

    1.Tensile strength kgf/mm? - 30 min

    2.Yield point or Proof stress kgf/mm? - No

    3.Elongation % - 35 mm

    4.Flattening strength 1/2 D

    5.Bending strength 180?

M7197

    Carbon Steel (JIS G 3131)

    1. General Statements

    1.1 Introduction

    Carbon Steel (JIS G 3131)

    2. Allowable Equivalents

    The following equivalent materials may be used to fulfill this Specification. One or more of the

    following methods may be used to specify materials, but do not duplicate information between

    methods.

    2.1 Existing industry specifications:

    Governing Body (ASTM, JIS, Specification Number

    etc.)Equivalent Material G3131 / G 3131JIS1

    Equivalent Material 3501KSD2

    Equivalent Material

    3

    2.2 Existing vendor specific (proprietary):

    Material SupplierSupplier Specification NumberEquivalent Material

    1

    Equivalent Material

    2

    Equivalent Material

    3

    3. Physical Composition

    3.1 Elemental Composition (including tolerance):Element (Copper, aluminum, etc.)Percentage requirement (with tolerance)

    SPHC 0.15max / SPHD 0.10max / SPHD 0.10 maxC%

    Mn%SPHC 0.60max / SPHD 0.50max / SPHD 0.50 max

    S%SPHC 0.050max / SPHD 0.040max / SPHD 0.030 max

    P%SPHC 0.050max / SPHD 0.040max / SPHD 0.035 max

Report this document

For any questions or suggestions please email
cust-service@docsford.com