DOC

Security Broadband Router

By Pamela Rivera,2014-04-05 09:39
15 views 0
Security Broadband RouterSecu

BiGuard 2/10/30 Series

Security Broadband Router

Release Note

    thVersion: 1.02j (15, September, 2005)

Note:

    ; There are 2 firmware files for each model. biguardX.v102j is the formal firmware release,

    biguardX.v102j.tmp is an intermediate temp file to help to upgrade from old firmware

    version to V1.02j

    ; If your BiGuard version number is less than 1.00o (for BiGuard30) or 1.00m (for

    BiGuard2/10), please upgrade temporary firmware first (biguardX.v102j.tmp), and then

    upgrade formal firmware (biguardX.v102j)

    ; Please do load default after you upgrade this new firmware to avoid some uncertain

    issues after upgrading the firmware.

New Features:

    ;

    Improvement:

    ; Show disconnecting message on WAN status after user disconnect ISP connection. Bug Fixed:

    ;

Known Issues:

    thVersion: 1.02i (15, September, 2005)

Note:

    ; There are 2 firmware files for each model. biguardX.v102i is the formal firmware release,

    biguardX.v102i.tmp is an intermediate temp file to help to upgrade from old firmware

    version to V1.02i

    ; If your BiGuard version number is less than 1.00o (for BiGuard30) or 1.00m (for

    BiGuard2/10), please upgrade temporary firmware first (biguardX.v102i.tmp), and then

    upgrade formal firmware (biguardX.v102i)

    ; Please do load default after you upgrade this new firmware to avoid some uncertain

    issues after upgrading the firmware.

New Features:

    ; Support Dynamic IP address (0.0.0.0) for IPSec VPN remote gateway IP address

    setting.(only for aggressive mode)

    ; Add IPSec Wizard for IPSec VPN function.

    ; Support SNMP for Device Management function.

    ; Support no-ip service for DDNS function.

    Improvement:

    ; Improve the compatibility issue with SafeNet client in aggressive mode. ; Support key Group 5 for IPSec VPN.

    ; Add intrusion detection log for system log and Email-Alert

    ; Add message after completing “save config to flash”.

    ; Add protocol type option to improve virtual server function.

    ; Add port range redirect option to improve virtual server function.. ; Modify the Virtual server web design :Merge port redirection and port mapping into one

    page

    ; Add protocol type option to improve Host URL Mappings function and modify the web

    design.

    ; Improve hardware link -detection for WAN.

    ; Dynamic IPSec VPN policy can run simultaneously.

    Bug Fixed:

    ; Fixed a counter bug for the hour of system time displaying.

    ; Fixed a WAN ISP connection bug .

Known Issues:

    thVersion: 1.02h (12, August, 2005)

Note:

    ; There are 2 firmware files for each model. biguardX.v102h is the formal firmware

    release, biguardX.v102h.tmp is an intermediate temp file to help to upgrade from old

    firmware version to V1.02h

    ; If your BiGuard version number is less than 1.00o (for BiGuard30) or 1.00m (for

    BiGuard2/10), please upgrade temporary firmware first (biguardX.v102d.tmp), and then

    upgrade formal firmware (biguardX.v102h)

    ; Please do load default after you upgrade this new firmware to avoid some uncertain

    issues after upgrading the firmware.

New Features:

    ; Add Current Time on status page.(\Status)

Improvement:

    ; Improve PPPoE performance.

    ; Add Edit button for Virtual server. It will improve the convenience to modify the

    settings.

    ; Add log message after NTP synchronize system time.

    ; Allow IPSec connection name to input numbers.

Bug Fixed:

    ; Fixed syslog will be cleaned after you press Apply of Time zone and e-mail alert page

    issue.

Known Issues:

    thVersion: 1.02f (4, August, 2005)

Note:

    ; There are 2 firmware files for each model. biguardX.v102d is the formal firmware

    release, biguardX.v102d.tmp is an intermediate temp file to help to upgrade from old

    firmware version to V1.02d

    ; If your BiGuard version number is less than 1.00o (for BiGuard30) or 1.00m (for

    BiGuard2/10), please upgrade temporary firmware first (biguardX.v102d.tmp), and then

    upgrade formal firmware (biguardX.v102d)

    ; Please do load default after you upgrade this new firmware to avoid some uncertain

    issues after upgrading the firmware.

New Features:

Improvement:

Bug Fixed:

    ; Fixed the user can't delete the 150th entry of MAC filter.

    ; Fixed the router will lockup after the user delete several MAC filters entries .

Known Issues:

    rdVersion: 1.02e (3, August, 2005)

Note:

    ; There are 2 firmware files for each model. biguardX.v102d is the formal firmware

    release, biguardX.v102d.tmp is an intermediate temp file to help to upgrade from old

    firmware version to V1.02d

    ; If your BiGuard version number is less than 1.00o (for BiGuard30) or 1.00m (for

    BiGuard2/10), please upgrade temporary firmware first (biguardX.v102d.tmp), and then

    upgrade formal firmware (biguardX.v102d)

    ; Please do load default after you upgrade this new firmware to avoid some uncertain

    issues after upgrading the firmware.

New Features:

Improvement:

Bug Fixed:

    ; Fixed Delete some entry of QoS rule will cause the other QoS rules missed.

Known Issues:

    thVersion: 1.02d (29, July, 2005)

Note:

    ; There are 2 firmware files for each model. biguardX.v102d is the formal firmware

    release, biguardX.v102d.tmp is an intermediate temp file to help to upgrade from old

    firmware version to V1.02d

    ; If your BiGuard version number is less than 1.00o (for BiGuard30) or 1.00m (for

    BiGuard2/10), please upgrade temporary firmware first (biguardX.v102d.tmp), and then

    upgrade formal firmware (biguardX.v102d)

    ; Please do load default after you upgrade this new firmware to avoid some uncertain

    issues after upgrading the firmware.

New Features:

    ; Add MAC filter function in \Configuration\Firewall\LAN MAC Filter\ . (150 rules max.)

    ; Add “Intrusion Detection function for preventing hacker attack from

    internet.(\Configuration\Firewall\Intrusion Detection\ )

    ; Add Up time for WAN connection status & System up time for system status

    page.(\Status)

    ; Add Username & Password of SMTP server authentication settings for Email-Alert

    function.

Improvement:

    ; Prevent user upload wrong system configuration file into BiGuard. ; Improve PPPoE connection speed.

    ; Increase the total numbers of QoS rule to 150.

Bug Fixed:

    ; Fix user cant ping WAN IP address from LAN.

Known Issues:

    thVersion: 1.01 (30, June, 2005)

Note:

    ; There are 2 firmware files for each model. biguardX.v101 is the formal firmware release,

    biguardX.v101.tmp is an intermediate temp file to help to upgrade from old firmware

    version to V1.01

    ; If your BiGuard version number is less than 1.00o (for BiGuard30) or 1.00m (for

    BiGuard2/10), please upgrade temporary firmware first (biguardX.v101.tmp), and then

    upgrade formal firmware (biguardX.v101)

    ; Please do load default after you upgrade this new firmware to avoid some uncertain

    issues after upgrading the firmware.

New Features:

    ; Add Failover function. (BiGuard30)

    ; Add IPSec Failover function. (BiGuard30)

    ; Add Inbound Load Balance function. (BiGuard30)

    ; Add Quality of Service.

    ; Add Big Pond, the Telstra ISP connection type.

    ; Add URL Filter function.

    ; Add several DDNS servers for DDNS update.

    o www.zoneedit.com

    o www.orgdns.org

    o www.dhs.org

    o www.dyns.cx

    o www.3domain.hk

    o www.3322.org

Improvement:

    ; Add IP address hash mechanism for Outbound Load Balance. This function will ensure

    that the same source IP / destination IP will go through the SAME WAN interface. This

    is useful if some server will authenticate the source IP address. (BiGuard30) ; Add WAN Interface option for IPSec setting. (BiGuard30)

    ; Add local Loop back to support the access of virtual server function locally. ; Add Save Log option in System log.

Bug Fixed:

    ; Fix BiGuard can not get IP from DHCP server correctly when WAN ISP mode set to

    Obtain IP address automatically.

    ; Fix Remote access function does not work issue.

    ; Fix DNS proxy could not function after some time.

    ; Fix Virtual Server does not work through WAN2 (BiGuard30)

    ; Fix an Outbound Load Balance surfing issue. For some web sites which will try to

    authenticate the user by checking the source IP address, the dual wan access might not

    work if we have no way to guarantee the same source IP address.(BiGuard30)

Known Issues:

    ;

Report this document

For any questions or suggestions please email
cust-service@docsford.com