DOCX

5501839 original manual(English)110517

By Victoria Ellis,2014-09-21 09:43
8 views 0
5501839 original manual(English)110517

     1

Original manual

    MULTI-TASK SHARPENER

    INSTRUCTION MANUAL

     1

     2

    SPECIFICATIONS MODEL NO. 5501839 Mains: AC 230V/50Hz

    Power: 65W (S3:15%, ON: 90S,OFF: 510S) Free speed: 6000RPM

    Wheel diameter: Dia.48mm * hole dia.10mm * thickness7.5mm

    Max. drill diameter: 10mm

    Min drill diameter: 3mm

    Net weight: 1.65KGS

    L74 dB(A) PA

    K 3 dB(A) PA

    L87 dB(A) WA

    k3 dB(A) WA

SAVE THIS MANUAL

    You will need the manual for the safety warnings and precautions, assembly instructions, operating and

    maintenance procedures, parts list and diagram. Keep the manual in a safe and dry place for future

    reference.

TABLE OF CONTENTS

SPEVIFICATIONS …………………………………………………………… Page 2

    TABLE OF CONTENTS ……………………………………………………. Page 2

    INTRODUCTION …………………………………………………………… Page 2

    SAFETY INSTRUCTIONS …………………………………………………… Page 3

    OPERATION …………………………………………………………………. Page 5

    RISK …………………………………………………………………………… Page 10

    LIST AND METHOD OF REPLACING WEAR PARTS ………………… Page 10

    MAINTENANCE ……………………………………………………………. Page 13

    CONTENTS …………………………………………………………………. Page 13

    PARTS LIST, WEEE & OTHERS …………………………………………… Page 14

INTRODUCTION

    This Multi-function Sharpener had been designed for sharpening drill bits, knives, scissors, chisels and

    blades. It is intended for DIY use only.

This Multi-function Sharpener is intended to be bolted down on a stable worktable with larger than 300 x

    300MM. The hole distance to fix the machine should be 121MM (Width) x 99MM (Length) , the proper

    screw should be M4 x 25MM

     2

     3

    SAFETY INSTRUCTIONS

     WARNING ! When using electric tools basic safety precautions should always be

     followed to reduce the risk of fire, electric shock and personal injury including the

     following. Read all these instructions before attempting to operate this product and

     save these instructions

ELECTRICAL SAFETY

    The electric motor has been designed for 230V only. Always check that the power supply corresponds to the voltage on the rating label. The machine is with two-pin plug, must be connected socket with a cable fusing.

    If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid a hazard.

1. Keep work area clear

    - Cluttered areas and benches invite injuries

    2. Consider work area environment

    - Do not expose tools to rain.

    - Do not use tools in damp or wet locations.

    - Do not use tools in the presence of flammable liquids or gases.

    - Make sure to put the sharpener on a stable surface and position.

    3. Guard against electric shock

    - Avoid body contact with earthed or grounded surfaces (e.g. pipes, radiators, ranges,

    refrigerators)

    4. Keep other persons away.

    - Do not let persons, especially children, not involved in the work touch the tool or the extension

    cord and keep them away from the work area.

    5. Store idle tools

    - When not in use, tools should be stored in a dry locked-up place, out of reach of children 6. Do not force the tool

    - It will do the job better and safer at the rate for which it was intended. 7. Use the right tool

    - Do not force small tools to do the job of a heavy duty tool.

    - Do not use tools for purposes.

    8. Dress properly

    - Do not wear loose clothing or jewellery, they can be caught in moving parts. 9. Do not abuse the cord

    - Never yank the cord to disconnect it from the socket. Keep the cord away from heat, oil and sharp edges.

    - Do not let the cord hang over the edge of table or counter or touch hot surfaces.

    10. Secure work

    - Where possible use clamps or a vice to hold the work. It is safer than using your hand. - Keep handles dry, clean and free from oil and grease.

     3

     4

    11. Do not overreach

    - Keep proper footing and balance at all times.

    12. Remove adjusting keys and wrenches

    - Form the habit of checking to see that keys and adjusting wrenches are removed from the

    tool before turning it on.

    13. Avoid unintentional starting

    - Ensure switch is in off position when plugging in.

    - Unplug from outlet when not in use, before putting on or taking off any parts and before cleaning. 14. Use outdoor extension leads

    - When the tool is used outdoors, use only extension cords intended for outdoor use and so

    marked.

    - Inspect extension cords periodically and replace if damaged.

    15. Stay alert

    - Watch what you are doing, use common sense and do not operate the tool when you are

    tired.

    16. Check damaged parts

    - Before further use of tool, it should be carefully checked to determine that it will operate properly and perform its intended function.

    - Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation.

    - Have defective switches replaced by an authorized service centre.

    - Do not use the tool if the switch does not turn it on and off.

    17. Warning

    - The use of any accessory or attachment other than one recommended in this instruction

    manual may present a risk of personal injury.

    18. Have your tool repaired by a qualified person.

    - This electric tool complies with the relevant safety rules. Repairs should only be carried out

    by qualified persons using original spare parts; otherwise this may result in considerable

    danger to the user.

Notice:

    *Adjust the spark arrestor frequently so as to compensate for wear of the wheel, keep the distance between the spark arrestor and the wheel as small as possible as and in any case not greater than 2 mm;

    *Instruction for the safe use, handling and storage of abrasive wheels taking into account the requirements of the CEN standard for abrasive products for the type of tool covered by this standard. It is assumed that wheels will not be dressed. If wheel dressing is intended then suitable precautions should be taken.

    *Do not operate any product with a damaged cord or plug, if the product malfunctions or it is dropped or damaged in any way.

    *Do not leave the grinding wheel unattended while it is operating.

    *Grinding generates sparks-keep away all flammable substances and materials.

    *Never touch the operating grinding wheel.

    *The motor is specially rated for intermittent use-maximum 15 minutes continuous use.

     4

     5

    *Do not attach modules when the grinding wheel is moving.

    *Do not use the grinding wheel without a module in place.

    *Before removing a module, switch off on the Power Unit and allow the grinding wheel to come to a stop.

USER PRECAUTIONS

     WARNING! Read all instructions, failure to follow all instructions listed below may

     result in electric shock, fire and / or serious injury.

    To protect against electrical shock, do not immerse cord, plug or appliance in water or any other liquid. Remove all loose clothing, neckties, rings, bracelets and other jewelry that may get caught in moving parts.

    Non-skid footwear is recommended when working outdoors.

    Wear protective hair covering to contain long hair.

    Ear muffs and gloves are recommended.

    Always use safety glasses. Note: Everyday eye glasses do not contain impact resistant lenses-they are NOT safety glasses.

    Always use face or dust masks if grinding operation is dusty.

     CARE AND CLEANING

     Before cleaning, disconnect from the mains.

     Keep clean and free from oil and grease.

     Store in dry conditions.

     5

     6

OPERATION

BEFORE SWITCHING THE POWER, PLEASE MAKE SURE THE ON/OFF SWITCH IS SET

    TO OFF, AND THEN PLEASE PLUG IN MAINS (AC 230V/ 50Hz)

THE OPERATOR SHOULD ALWAYS STAND IN FRONT OF THE MACHINE DURING

    USING.

    If the machine gets jammed during using, please shut off the power immediately and take out the jammed accessories and restart the machine, if it still does not work properly, please bring the machine to our service department (detailed address please see end this manual) or make sure it is repaired by a qualified technician.

     6

     7

Sharpens all high speed steel drill bits from 7/64 (3.1mm) to 3/8 (10mm)

    Unique True Point action ensures accurate finish

    Precisely locates high speed steel drills for correct sharpening angles

    Re-sharpens broken drill bits

SHARPENING HSS BITS

    1. Slide module, labeled high speed steel drill sharpener onto the Power Unit.

    2. Remove the clamp from the clamp holder and insert the drill bit to be sharpened (1a).Tighten the

    clamp lightly

    to leave the drill bit still free to move.

    3. Place the clamp containing your drill bit into the setting slot, using the grooves in the side to lower it

    in

    correctly (1b).

    4. Move the drill tit forward up so that it lays in the V guide and touches the metal end stop (1c).

    5. Turn the drill bit until the V guide fully drops over it (1c)-all four drill bit corners should now be touching the

    V guide sides.

    6. Ensure that the drill and holder are fully down in the setting slot. With the drill bit in this position, tighten the

     clamping ring(1d).

    7. Lift up the V guide and remove the clamp and drill bit.

    8. Transfer the clamp holder from side to side, securing with light finger pressure (1f). 9. Switch the Power Unit on.

    10. Move the clamp holder from side to side,securing with light finger pressure (1f). 11. Remove the drill bit and holder and turn over (1g). Repeat No.11.

    12. Check the leading edge of both flutes are equally sharp. They should meet exactly in the middle as in

    (1h),not (1i).

    13. Switch the Power Unit off. Before removing the module, ensure the grinding wheel has stopped.

     7

     8

    Sharpens all straight edged knives & scissors. Unique top for sharpening knives.

    Precisely angled slot for sharpening scissors.

SHARPENING KNIVES

    1. Slide module, labeled Knife & Scissor Sharpener on to the Power Unit.

    2. Switch the Power Unit on.

     8

     9

    3. Hold the knife handle towards you and insert the handle end of the blade into guide slot (2a). 4. As soon as the blade touches the grinding wheel, draw it with light steady pressure across the wheel

    to the tip-

    then remove. Do not press hard (2b).

    5. Insert the second side of the blade into the other top guide slot (2c) and repeat #4. 6. Repeat sharpening each side in turn until a clean sharp edge is attained.

    7. Switch the Power Unit off. Before removing the module, ensure that the grinding wheel has stopped.

SHARPENING SCISSORS

    1. Slide module. Labeled Knife & Scissor Sharpener, onto the Power Unit.

    2. Switch the Power Unit on.

    3. Open the scissors fully.

    4. Slide the first scissor blade through the front guide slot (2d)-keep the pivot of the scissors and other

    blade to

    Right hand side.

    5. Draw the blade across the grinding wheel from pivot to tip. Use a light steady pressure, do not press too hard

     (2e).

    6. Remove and turn scissors over to sharpen the second blade (2f)-keep the pivot to the right and sharpen from

    7. Repeat if necessary, until clean sharp edges are achieved.

    8. Switch the Power Unit off. Before removing the module, ensure that the grinding wheel has stopped

     9

     10

Regrinds Chisel & Plane blades up to 2 (50mm) wide

    Adjustable grinding angle from 20?- 40?

    Powerful integral magnet to keep blade secure Protecive shield for added safety

SHARPENING BLADES

    1. Slide Chisel & Plane Sharpener Power Unit. 2. Place the blade against the back lip of the plate (3a). The magnet helps hold in place.

     10

Report this document

For any questions or suggestions please email
cust-service@docsford.com