DOC

Brushless Motor speed controller user guide

By Carol Hunter,2014-12-28 12:43
8 views 0
Brushless Motor speed controller user guide

     Brushless Motor speed controller Manual

     W12A/ W25A/W30A

Operation Limit:

    12A: max current 15A, continuous current 12A for 10 minutes

    25A: max current 30A, continuous current 25A for 10 minutes

    30A: max current 35A, continuous current 30A for 10 minutes

Voltage Range: 6V-12V

    Number of Batteries: 4-12NiMH, 2-3LiPo

    BEC Output: 5V1.5A.2LiPo\4-5mini servo, 3Lipo\3-4mini servo

    Protective Functions:

    ? Automatically select 2-3LiPo,protective voltages are 6V/9V respectively; ? Automatically select NiMH, the protective voltage for each battery is 0.8V. ? Safe start will not start if the throttle stick is not in the right position; ? Temperature protection, shutdown if the surface temperature reaches 110?

    ? lost of control protection, shutdown after I second without signal. Performance:

    ? motor limit:

    ? 2-pole adversion as high as 300000rpm

    ? 12-pole adversion 50000rpm

    ? 14-pole adversion 42000rpm

? For 8KHzpWM control ,

    ? Position of the full, throttle will be adjust automatically

    ? BEC and MCU use separate power supply for table operation.

    Setting Method:

    1. Open the transmitter, switch throttle stick to the full power position (for FUTABA series

    transmitter, the throttle stick shall be switched to REV).

    2. Connect the receiver and motor.

    3. Connect the power to the speed controller.

    4 If the transmitter is in normal condition, it will have the following sound: (if there are no more

    sounds after a long low sound at the end of this sound, check the reverse setting of the

    transmitter throttle channel).

     ? B: indicates LIPO automatic protection

     ? BB BB: indicates NiMH/NiCD automatic protection

     ? BBB BBB: indicates brake selection

    5. If there is setting you want in the process of sound cycle, switch the throttle

    stick, to the lowest position at the first time interval. (For example, select

    LIPO automatic protection: switch the throttle stick to the lowest position when

    hearing one B sound)

    6. If there is another additional setting, quickly switch the gun to the highest position to make a

    selection.

    7. If you have finished the setting you require, wait 2 seconds and the motor will send a

    confirmation sound for battery protection. It is usable after confirming the position of throttle

    stick.

    8. LIPO automatic protection has only 2 voltage protection points, i.e 6V and 9V. There is no

    need to use a full capacity battery.

    9. NiMH automatic protection is calculated according to the real number of batteries. Sets

    0.8V for each battery. In order to ensure accurate judgment of the battery voltage, please

    charge the battery to full capacity. If the battery is not at full capacity. The speed controller

    will estimate the protection voltage according to 53% of the full capacity.

    10. the brake is seeing as default set

    11. Reset the brake operation to release the brake function. .

    12. Factory parameter reset function: because this series of electronic governor has an

    overheating and false operation protective function, if you find that the speed controller is

    accelerating or changing is direction, or the throttle is different from the original condition,

    you can reset the factory parameters to obtain the highest performance.

    When starting the machine there is a long B sound. It indicates that the electronic governor is

    in LIPO protection mode. The BBB sound indicates that it is in NiMH/NiCD automatic

    protection mode.

    TOWERPRO CO.LTD BRUSHLESS MOTOR CONTROLLER

    SETUP MENU for 50A and 70A NO POWER OUTPUT TO RECEIVER

    Current

    Type Dimension BEC Voltage Battery Protective Continuous Moment (10minutes)

    5V/3A 4/5 /6LIPO 50A 55A 50A 43×38×10mm LIPO 4-6 on-off type protective NIMH/Nicd13-25V manostat or voltage 70A 75A 70A 58×38×12mm 12-18 OPTO 13/15V/18V 1. Connect the motor and receiver to the speed controller 2. Move throttle stick on full power position (UP Position) 3. Turn on the transmitter.

    4. Reconnect battery power to the speed controller After 3 sec you can hear (all sound is 3 times) ?— CELL Type and Number

    ?— BRAKE

    ?— TIMING MODE

    ?— PWM

    ON you need programming menu, move the throttle stick to the middle position~

    1. CELL Type and Number SET

     •— NiMh/Nicd AUTO0.8V/CELL

     •— 4LIPO 2.75V/CELL

     •— 5LIPO2.75V/CELL

     •— 6LIPO2.75V/CELL

    2. BRAKE SET

    ••— NO

    •••— SOFT

    •••— MID

    •••— HARD

    3. TIMING MODE SET

     •••—

    ••••— 8 º

    •••••— 15º

    •••••— 30º

    4. PWM SET

     ????— 8KHZ

     ????— 16KHZ

     ????— 32KHZ

    IF the option is you need, then move the throttle stick to UP position.

    The long BEEP is save the option. And the system will go to the programming menu.

    You can setup other options.

    When all you need option is setup ok, push the throttle stick to down position, after

1 sec the system will save all option, and then you can start the motor now!!

    TOWERPRO CO.LTD BRUSHLESS MOTOR CONTROLLER

    SETUP MENU (for new 18A /20A)

    First, connect the motor and receiver to the speed controller

    Remove battery power from the speed controller. Turn on the transmitter.

    Move throttle stick on full power position (UP Position) Reconnect battery power to the speed controller After 3 sec you can hear (all sound is 3 times) ?— CELL Type AND Number

    ?— BRAKE

    ?— TIMING MODE

    ?— Voltage Protection

    ON you need programming menu, move the throttle stick to the middle position

    5. Cell type and number SET

     •—

     •— 2LIPO 7.4V

     •— 3LIPO11.1V

    6. BRAKE SET

    ••— NO

    •••— SOFT

    •••— MID

    •••— HARD

    7. TIMING MODE SET

     •••—

    ••••— 7 º

    •••••— 15º

    •••••— 30º

    8. Voltage Protection

     ••••— 2.8V/CELL

    •••••— 2.9V/CELL

    •••••••— 3.0V/CELL

    Attention: 10C or higher battery suggest select the 3.0V as the protection voltage.

    IF the option is you need, then move the throttle stick to UP position.

    The long BEEP is save the option. And the system will go to the

    programming menu. You can setup other options.

    When all you need option is setup ok, push the throttle stick to down position, after 1 sec the system will save all option, and then you can start the motor now.

    Tower Pro Brushless Speed Controller

    Manual

    100A

    The restrictions on the use of the 100A Brushless ESC:

    1. The ambient air.

    2. The current cannot exceed 50A and the time cannot exceed one minute when the throttle

    stick to the middle position.

    Basic character

    Current Protective Type Dimension BEC Voltage Battery continuousfunction moment 10minutes

    4-6-8 LIPO LIPO 4-8 protective 100A 120A 110A 75×55×20mm OPTO 13-32V NIMH/Nicdvoltage is 12-24 13/18/24V

Setting way

    1. Connect the motor and receiver to the speed controller

    2. Move throttle stick on full power position, (UP Position)

    3. Turn on the transmitter.

    4. Reconnect battery power to the speed controller. After 3sec you can hearall sound is 3times)

    ?— Cell Type and Number

    ?— Brake

    ?— Timing Mode

    ?— PWM If you need programming menu, move the throttle stick to the middle position

    1. CELL Type and Number Set

    ?— NIMh / Nicd AUTO (0.8V/CELL)

    ?— 4LIPO 2.75V/CELL

    ?— 6LIPO (2.75V/CELL)

    ?— 8LIPO (2.75V/CELL)

    2. BRAKE SET

    ??— NO

    ??— SOFT

    ??— MID

    ??— HARD

    3. TIMING MODE SET

    ???— 3?

    ???— 8?

    ???— 15?

    ???— 30?

    4. PWM SET ;频率设定,

    ????— 8KHZ 8

    ????— 16KHZ 16

    ????— 32KHZ 32 IF the option is you need, then move the throttle stick to UP position. The long BEEP is save the option. And the system will go to the programming menu. You can setup other options.

    When all you need option is setup OK, push the throttle stick to down position, after 1sec the system was save all option, and then you can start the motor now!!

Report this document

For any questions or suggestions please email
cust-service@docsford.com