DOC

SECTION 09900

By Leonard Fisher,2014-01-09 11:53
11 views 0
SECTION 09900

    Diamond Vogel Paints

    1110 Albany Place SE

    Orange City, IA 51041

    (712) 737-8880

    www.diamondvogel.com

    SECTION 09 91 23

    INTERIOR PAINTING

    MEETS THE REQUIREMENTS FOR

    LEED?-NC v. 2.2

    PART 1 GENERAL

    1.1RELATED DOCUMENTS

    A.Drawings and general provisions of the Contract, including General and Supplementary

    Conditions and Division 1 Specification Sections, apply to this Section.

    1.2SUMMARY

    A.Section includes surface preparation and field application of interior and exterior paints,

    coatings, stains and varnishes.

    1.3RELATED SECTIONS

    A.Section 05 12 00-Structural Steel: Shop priming.

    B.Section 05 50 00-Metal Fabrications: Shop priming.

    C.Section 06 20 00-Finish Carpentry: Back priming of trim.

    D.Section 09 91 13-Exterior Painting.

    E.Section 09 60 00-High Performance Coatings.

    F.Section 22 05 53-Mechanical Identification: Markers and color-coding schemeG.Section 26 05 53-Electrical Identification: Markers and color-coding schemeH.Section 32 10 00-Bases, Ballasts, Pavements and Appurtenances: Traffic marking paint.

    1.4REFERENCES

    A.ASTM D 16-Terminology Relating to Paint, Varnish, Lacquer, and Related Products.B.SSPC-SP-2-Hand Tool Cleaning, 1982.

    C.SSPC-SP-3-Power Tool Cleaning, 1982.

    D.SSPC-SP-6-Commercial Blast Cleaning, 2000.

    E.Green Seal GS-11, Paints, May 20, 1993.

    F.Green Seal GC-03, Anti-Corrosive Paints, January 7, 1997.

    G.South Coast Air Quality Management District (SCAQMD) Rule 1113, Architectural Coatings,

    July 9, 2004.

    H.LEED?-NC version 2.2, Green Building Rating System for New Construction and Major

    Renovations, October, 2005.

    Paints and Coatings

     09 91 23-1

    1.5SUBMITTALS

    A.Submit under provisions of Section 01 30 00.

    B.Product Data and Material Safety Data Sheets (MSDS): Submit a material list,

    manufacturer’s data sheet and MSDS for each paint system indicated as required by USGBC

    for certification. Include information for all primers, undercoats and block fillers.C.Application Instructions: Provide coating manufacturer’s printed application instructions for

    each product, including product storage and surface preparation instructions.D.Selection Samples: Provide two sets of color chips representing manufacturer’s full range of

    colors.

    E.Verification Samples: Provide two samples 6 inches square of actual product, color and

    sheen for each painting system specified. Samples shall include primers, sealers or

    blockfillers. Apply each coat stepped, defining each separate coat.

    1.6QUALITY ASSURANCE

    A.Manufacturer Qualifications: Company specializing in manufacture of products specified in

    this Section for a minimum of 10 years.

    B.Applicator Qualifications: Company experienced in applying paints and coatings similar to

    those specified in this Section with a minimum of 5 years documented experience.C.Source Limitations: Provide materials from the same manufacturer for each specified paint

    system.

    D.Mock-Ups: Provide benchmark samples for each type of finish system, sheen and substrate

    indicated.

    1.Architect will select area to represent surfaces for each system specified in Part 3.

    a.Wall and Ceiling Surfaces: Provide samples of at least 100 square feet.

    b.Door and Frame Surfaces: Provide sample assembly.

    c.Other Substrates: Architect will designate items or areas required.

    1.7DELIVERY, STORAGE AND HANDLING

    A.Deliver products to site in manufacturer’s original, sealed, and labeled container.B.Manufacturer’s label shall include the following information:

    1.Product name

    2.Product code number

    3.Product lot number

    4.Application instructions

    5.Surface preparation instructions

    6.Cleanup requirements

    7.Color designation

    8.Thinning instructions

    C.Store materials until use according to manufacturer’s instructions in a well-ventilated area.D.Store and dispose of solvent-based materials in accordance with requirements of local

    authorities having jurisdiction over project.

    Paints and Coatings

     09 91 23-2

    1.8PROJECT CONDITIONS

    A.Apply coatings only when environmental conditions recommended by the manufacturer are

    met.

    B.Do not apply coatings in snow, rain, fog or mist, or when temperatures are less than 5

    degrees F above the dew point. Do not apply materials to damp or wet surfaces.C.During application of coating materials, mark areas with “Wet Paint” signs.

    1.9EXTRA MATERIALS

    A.Furnish for each product, color and finish specified 2 gallons of coating material, in sealed 1-

    gallon containers, clearly marked with color and manufacturer’s label.

    PART 2 - PRODUCTS

    2.1MANUFACTURERS

    A.Acceptable Manufacturer: Diamond Vogel Paints (DVP), 1110 Albany Place SE, Orange

    City, IA 51041 Telephone: 866-DVP-SPEC. Website: www.diamondvogel.com.

    [B.Requests for substitution will be considered in accordance with Section 01 60 00-Product

    Requirements.]

    [C.Substitutions: Not permitted.]

    2.2MATERIALS

    A.Paints and Coatings – General:

    1.Provide factory mixed coatings, except for field-catalyzed coatings. When required, mix

    coatings according to manufacturer’s instructions prior to application. Do not dilute or

    thin coatings, except as recommended by manufacturer.

    2.Do not add additives, except as instructed by manufacturer.

    3.For opaque finishes, tint each coat, including primer coat one half lighter shade than

    succeeding coat, with final finish coat being the specified shade.

    4.Colors: To be selected from manufacturer’s full range of architectural colors.B.Accessory Materials: Provide materials necessary to achieve finishes specified including but

    not limited to thinners, cleaning agents and sanding aides as recommended by coating

    manufacturer.

    C.VOC Limitations for Interior Coatings: Coatings must meet the following VOC limitations.

    1.Flat Coatings: 50 grams per liter or less.

    2.Non-Flat Coatings or Primers: 150 grams per liter or less.

    3.Wood Stains: 250 grams per liter or less.

    4.Clear Wood Finishes: 275 grams per liter or less.

    2.3WATER-BASED PRIMERS

    A.Interior/Exterior Acrylic Rust-inhibitive Maintenance Primer:

    1.VOC Content: 91 grams per liter.

    2.Dry film thickness per coat: 2 to 3 mils.

    3.Product: DVP V-Cote 200 Acrylic Maintenance Primer/Finish, MC-Series.B.Interior/Exterior Acrylic Universal Primer

    Paints and Coatings

     09 91 23-3

    1.VOC Content: 95 grams per liter.

    2.Dry film thickness per coat: 1.5 to 2.0 mils.

    3.Product: DVP Diamond Prime Universal Interior/Exterior Primer, MU-1501.

    C.Interior Low-Odor, Zero-VOC Primer/Sealer:

    1.VOC Content: 0 grams per liter.

    2.Dry film thickness per coat: 2.0 to 3.0 mils.

    3.Product: DVP Health Kote Zero VOC Interior Primer/Sealer, DU-1590.D.Interior Primer/Sealer:

    1.VOC Content: 48 grams per liter.

    2.Dry film thickness per coat: 2.0 to 3.0 mils.

    3.Product: DVP Vantage Primer Interior Latex Primer/Sealer, DU-1511.E.Interior Primer/Surfacer:

    1.VOC Content: 67 grams per liter.

    2.Dry film thickness per coat: 2.0 to 3.0 mils.

    3.Product: DVP Pre-Tex Interior Primer/Surfacer, DU-1520.F.Interior Latex Enamel Undercoater:

    1.VOC Content: 56 grams per liter.

    2.Dry film thickness per coat: 1.0 to 1.5 mils.

    3.Product: DVP Interior Latex Enamel Undercoater, DU-1508.

    2.4BLOCK FILLERS

    A.Interior Acrylic Block Filler:

    1.VOC Content: 62 grams per liter.

    2.Dry film thickness per coat: 5.0 to 15.0 mils.

    3.Product: DVP Dia-Pro Acrylic Block Filler, BF-1515.

    2.5WATER-BASED FINISHES

    A.Interior/Exterior Spray Acrylic Satin Enamel:

    1.VOC Content: 107 grams per liter.

    2.Dry film thickness per coat: 1.0 to 1.5 mils.

    3.Product: DVP Super Quick 30 Interior/Exterior Latex Satin Spray Enamel,

    DS-1561.

    B.Interior Eggshell Latex Enamel:

    1.VOC Content: <100 grams per liter.

    2.Dry film thickness per coat: 2.0 to 3.0 mils.

    3.Product: DVP Vantage Plus Interior Latex Eggshell Enamel, DE-Series.

    C.Interior Flat Latex Enamel:

    1.VOC Content: <47 grams per liter.

    2.Dry film thickness per coat: 2.0 to 3.0 mils.

    3.Product: DVP Vantage Plus Interior Latex Flat Enamel, DF-Series.D.Interior Gloss Latex Enamel:

    Paints and Coatings

     09 91 23-4

    1.VOC Content: 60 grams per liter.

    2.Dry film thickness per coat: 2.0 to 3.0 mils.

    3.Product: DVP Pro Plus Interior Latex Gloss Enamel, DH-Series.E.Interior Latex Dry Fall Flat:

    1.VOC Content: <32 grams per liter.

    2.Dry Film Thickness per Coat: 2.0 to 2.5 mils.

    3.Finish/Sheen: 0 to 10 at 85 degrees.

    4.Light Reflectance (White): 88.5 percent.

    5.Product: V-Cote 300 Latex Dri-Mist Flat, MV-Series.F.Interior Latex Dry Fall Semi-Gloss:

    1.VOC Content: 1 gram per liter.

    2.Dry Film Thickness per Coat: 2.0 to 2.5 mils.

    3.Finish/Sheen: 15 to 25 at 60 degrees.

    4.Light Reflectance (White): 88.5 percent.

    5.Product: V-Cote 303 Latex Dri-Mist Semi-Gloss, MV-Series.G.Interior Low-Odor, Zero-VOC Eggshell Latex:

    1.VOC Content: 0 grams per liter.

    2.Dry film thickness per coat: 1.5 to 2.0 mils.

    3.Product: DVP Health-Kote Interior Latex Eggshell, DE-1591.H.Interior Low-Odor, Zero-VOC Flat Latex:

    1.VOC Content: 0 grams per liter.

    2.Dry film thickness per coat: 1.5 to 2.0 mils.

    3.Product: DVP Health-Kote Interior Latex Flat, DF-1591.I.Interior Low-Odor, Zero-VOC Semi-Gloss Latex:

    1.VOC Content: 0 grams per liter.

    2.Dry film thickness per coat: 1.5 to 2.0 mils.

    3.Product: DVP Health-Kote Interior Latex Semi-Gloss, DS-1591.J.Interior Semi-Gloss Latex Enamel:

    1.VOC Content: 97 grams per liter.

    2.Dry film thickness per coat: 2.0 to 3.0 mils.

    3.Product: DVP Vantage Plus Interior Latex Semi-Gloss Enamel, DS-Series.

    2.5WATERBORNE EPOXY FINISHES

    A.Waterborne Gloss Epoxy Finish:

    1.VOC Content: <115 grams per liter.

    2.Dry film thickness per coat: 2.0 to 2.5 mils.

    3.Product: DVP Aqua Pox Waterborne Epoxy with Gloss Activator,

    MC-Series/MF-0240.

    B.Waterborne Polyamide Epoxy Finish:

    Paints and Coatings

     09 91 23-5

    1.VOC Content: 37 grams per liter.

    2.Dry film thickness per coat: 2.0 – 3.0 mils.

    3.Product: DVP V-Cote 111 Waterborne Polyamide Epoxy, MF-1210/MM-0210.C.Waterborne Semi-Gloss Epoxy Finish:

    1.VOC Content: <115 grams per liter.

    2.Dry film thickness per coat: 2.0 to 2.5 mils.

    3.Product: DVP Aqua Pox Waterborne Epoxy with Semi-Gloss Activator,

    MC-Series/MF-0245.

    2.6INTERIOR WOOD STAINS/FINISHES

    A.Interior High Solids Penetrating Stain:

    1.VOC Content: 240 grams per liter.

    2.Dry film thickness per coat: not applicable.

    3.Product: Old Master’s Hi-Solids Penetrating Stain.

    B.Interior Water-Reducible Acrylic Sanding Sealer:

    1.VOC Content: 270 grams per liter.

    2.Dry film thickness per coat: 1.0 to 2.0 mils.

    3.Product: DVP Old Master’s HO Acrylic Sanding Sealer.2

    C.Interior Water-Reducible Polyurethane Gloss Finish:

    1.VOC Content: <275 grams per liter.

    2.Dry film thickness per coat: 1.0 to 2.0 mils.

    3.Product: DVP Old Master’s HO Acrylic Gloss Polyurethane.2

    D.Interior Water-Reducible Polyurethane Satin Finish:

    1.VOC Content: <275 grams per liter.

    2.Dry film thickness per coat: 1.0 to 2.0 mils.

    3.Product: DVP Old Master’s HO Acrylic Satin Polyurethane.2

    E.Interior Water-Reducible Polyurethane Semi-Gloss Finish:

    1.VOC Content: <275 grams per liter.

    2.Dry film thickness per coat: 1.0 to 2.0 mils.

    3.Product: DVP Old Master’s HO Acrylic Semi-Gloss Polyurethane.2

    PART 3 EXECUTION

    3.1EXAMINATION

    A.Verify that surfaces and substrates are free of surface imperfections and containments that

    could inhibit performance or appearance of coatings. Report immediately any condition that

    may affect coating application, performance or appearance prior to starting any work.

    B.Test shop applied primers for compatibility with subsequent primers or finish systems.

    C.Ensure substrates’ moisture content is within tolerances recommended by coating

    manufacturer prior to application of coatings.

    D.Ensure concrete and masonry surfaces’ pH level is within tolerances recommended by

    coating manufacturer prior to application of coatings.

    Paints and Coatings

     09 91 23-6

    3.2PREPARATION

    A.Do not apply coatings until substrates are free of conditions that will inhibit proper coating

    adhesion or appearance.

    B.Immediately prior to application of coating, remove all dust, dirt, and other foreign matter from

    substrate.

    C.Stains and Marks: Remove completely if possible with products recommended by the coating

    manufacturer. If removal is not possible, spot-prime areas with a stain-blocking primer

    recommended by coating manufacturer.

    D.Aluminum Surfaces: Remove surface contamination or passivators by scrubbing with

    cleaning and etching solution recommended by coating manufacturer.

    E.Concrete and Masonry Surfaces: Remove all dirt, dust, efflorescence, wax, oil, grease, chalk

    and other contamination that may interfere with coating adhesion. Level all surface

    projections and mortar spatters by stoning. Rake mortar joints clean and remove all soluble

    salts. New concrete must cure for a minimum of 30 days at 72 degrees F prior to coating

    application.

    F.Galvanized Surfaces: Remove surface contamination and passivators by scrubbing with

    cleaning and etching solution recommended by coating manufacturer.

    G.Gypsum Board Surfaces: Fill imperfections with spackling compound and allow to dry. Spot-

    prime imperfections after repair with primer recommended by coating manufacturer.H.Interior Wood Surfaces Scheduled for Paint: Sand smooth any exposed wood surfaces.

    Patch nail holes and imperfections with wood filler or putty and sand smooth. Remove

    sanding dust.

    I.New Interior Wood Surfaces Scheduled for Clear Finishes: Remove dirt, dust, wax or grease

    prior to coating. Wood surface must be clean and dry. Eliminate imperfections by sanding

    the wood thoroughly; begin with medium grit sandpaper progressing to fine grit. Remove

    sanding dust prior to application. Sand in-between coats, removing sanding dust prior to

    application of next coat.

    J.Uncoated Ferrous Metal Surfaces: Abrasive blast new steel to SSPC-SP-6. Use proper

    abrasive to achieve an average of 1.5 - 2.0-mil blast profile. Blasted surfaces must be primed

    before flash rusting occurs.

    K.Uncoated Ferrous Metal Surfaces: Remove loose rust and mill scale with hand or power

    abrading tools as per SSPC-SP-2 and SSPC-SP-3.

    L.Shop-Primed Ferrous Metal Surfaces: Power or hand-wash to remove contamination. If oil

    or grease is present, use a cleaner/degreaser recommended by coating manufacturer.

    Remove all loose coatings, rust and corrosion by scraping, sanding or other abrading method

    as per SSPC-SP-2 and SSPC-SP-3. Use sandpaper to dull slick, glossy or non-porous

    surfaces.

    M.Doors: Seal top and bottom of door with sealer recommended by coating manufacturer.

    3.3APPLICATION

    A.Apply each coat to uniform coating thickness recommended by coating manufacturer.B.Apply materials to provide total color and sheen uniformity on all surfaces, regardless of

    number coats that might be required.

    Paints and Coatings

     09 91 23-7

    C.Allow each coat to dry thoroughly before application of next coat. Ensure proper coating

    adhesion of each coat prior to application of next coat.

    D.Remove dust, debris and other foreign materials from substrate prior to applying each coat.E.Produce finish free from shadows, roller shading, roller tailing, sags or hat banding.F.Contractor will be responsible for damage due to application of coatings to surfaces not

    scheduled for painting.

    3.4CLEANING

    A.Remove spills, spatters, and paint from all surfaces not scheduled for painting.B.Collect material that may create a fire hazard and store in metal bucket. Remove from

    premises on a daily basis.

    3.6SCHEDULE – INTERIOR PAINT SYSTEMS

    A.Gypsum Board.

    1.Interior [Flat] [Eggshell] [Semi-Gloss] [Gloss] Latex Enamel Finish System: Provide 2 coats of finish

    over a [zero VOC primer] [primer/sealer] [primer/surfacer].

    [a.Prime Coat: Interior Low-Odor, Zero VOC Primer/Sealer.]

    [a. Prime Coat: Interior Primer/Sealer.]

    [a. Prime Coat: Interior Primer/Surfacer.]

    b.Finish Coat: Interior [Flat] [Eggshell] [Semi-Gloss] [Gloss] Latex Enamel.

    2.Interior [Flat] [Eggshell] [Semi-Gloss] Low-Odor, Zero-VOC Latex Finish System: Provide

    2 coats of finish over a [zero VOC primer] [primer/sealer] [primer/surfacer].

    [a.Prime Coat: Interior Low-Odor, Zero VOC Primer/Sealer.]

    [a. Prime Coat: Interior Primer/Sealer.]

    [a. Prime Coat: Interior Primer/Surfacer.]

    b.Finish Coat: Interior Low-Odor, Zero-VOC [Flat] [Eggshell] [Semi-Gloss] Latex.

    3.Interior [Semi-Gloss] [Gloss] Waterborne Epoxy System: Provide 2 coats of finish over a

    [zero VOC primer] [primer/sealer].

    [a.Prime Coat: Interior Low-Odor, Zero VOC Primer/Sealer.]

    [a. Prime Coat: Interior Primer/Sealer.]

    b.Finish Coat: Waterborne [Semi-Gloss] [Gloss] Epoxy Finish.

    4.Interior Waterborne Polyamide Epoxy System: Provide 2 coats of finish over a [zero

    VOC primer] [primer/sealer].

    [a.Prime Coat: Interior Low-Odor, Zero VOC Primer/Sealer.]

    [a. Prime Coat: Interior Primer/Sealer.]

    b.Finish Coat: Waterborne Polyamide Epoxy Finish.

    B.Plaster.

    1.Interior [Eggshell] [Semi-Gloss] [Gloss] Latex Enamel Finish System: Provide 2 coats of

    finish over a [zero VOC primer] [primer/sealer] [primer/surfacer].

    [a.Prime Coat: Interior Low-Odor, Zero VOC Primer/Sealer.]

    Paints and Coatings

     09 91 23-8

    [a. Prime Coat: Interior Primer/Sealer.]

    [a. Prime Coat: Interior Primer/Surfacer.]

    b.Finish Coat: Interior [Flat] [Eggshell] [Semi-Gloss] [Gloss] Latex Enamel.2.Interior [Flat] [Eggshell] [Semi-Gloss] Low-Odor, Zero-VOC Latex Finish System: Provide

    2 coats of finish over a [zero VOC primer] [primer/sealer] [primer/surfacer].

    [a.Prime Coat: Interior Low-Odor, Zero VOC Primer/Sealer.]

    [a. Prime Coat: Interior Primer/Sealer.]

    [a. Prime Coat: Interior Primer/Surfacer.]

    b.Finish Coat: Interior Low-Odor, Zero-VOC [Flat] [Eggshell] [Semi-Gloss] Latex.3.Interior [Semi-Gloss] [Gloss] Waterborne Epoxy System: Provide 2 coats of finish over a

    [zero VOC primer] [primer/sealer].

    [a.Prime Coat: Interior Low-Odor, Zero VOC Primer/Sealer.]

    [a. Prime Coat: Interior Primer/Sealer.]

    b.Finish Coat: Waterborne [Semi-Gloss] [Gloss] Epoxy Finish.

    C.Ferrous Metal – Hollow Metal Doors, Frames and Other Steel.

    1.Interior Satin Spray Latex Enamel Finish System: Provide 2 finish coats over a primer.

    a.Prime Coat: Interior/Exterior Acrylic Rust-inhibitive Maintenance Primer.

    b.Finish Coat: Interior/Exterior Spray Acrylic Satin Enamel.

    2.Interior [Semi-Gloss] [Gloss] Waterborne Epoxy System: Provide 2 finish coats over a

    primer.

    a.Prime Coat: Interior/Exterior Acrylic Rust-inhibitive Maintenance Primer.

    b.Finish Coat: Waterborne [Semi-Gloss] [Gloss] Epoxy Finish.

    3.Interior [Eggshell] [Semi-Gloss] Low-Odor, Zero-VOC Latex Finish System: Provide 2

    coats of finish over a primer.

    a.Prime Coat: Interior/Exterior Acrylic Rust-inhibitive Maintenance Primer.

    b.Finish Coat: Interior Low-Odor, Zero-VOC [Eggshell] [Semi-Gloss] Latex.4.Interior [Eggshell] [Semi-Gloss] [Gloss] Latex Enamel Finish System: Provide 2 coats of

    finish over a primer.

    a.Prime Coat: Interior/Exterior Acrylic Rust-inhibitive Maintenance Primer.

    b.Finish Coat: Interior [Eggshell] [Semi-Gloss] [Gloss] Latex Enamel.5.Interior Waterborne Polyamide Epoxy System: Provide 2 coats of finish over a primer.

    a.Prime Coat: Interior/Exterior Acrylic Rust-inhibitive Maintenance Primer.

    b.Finish Coat: Waterborne Polyamide Epoxy Finish.

    D.Galvanized or Zinc-Coated Metal.

    1.Interior Satin Spray Latex Enamel Finish System: Provide 2 finish coats over a primer.

    a.Prime Coat: Interior/Exterior Acrylic Rust-inhibitive Maintenance Primer.

    b.Finish Coat: Interior/Exterior Spray Acrylic Satin Enamel.

    2.Interior [Semi-Gloss] [Gloss] Waterborne Epoxy System: Provide 2 finish coats over a

    primer.

    Paints and Coatings

     09 91 23-9

    a.Prime Coat: Interior/Exterior Acrylic Rust-inhibitive Maintenance Primer.

    b.Finish Coat: Waterborne [Semi-Gloss] [Gloss] Epoxy Finish.

    3.Interior [Eggshell] [Semi-Gloss] Low-Odor, Zero-VOC Latex Finish System: Provide 2

    coats of finish over a primer.

    a.Prime Coat: Interior/Exterior Acrylic Rust-inhibitive Maintenance Primer.

    b.Finish Coat: Interior Low-Odor, Zero-VOC [Eggshell] [Semi-Gloss] Latex.4.Interior [Eggshell] [Semi-Gloss] [Gloss] Latex Enamel Finish System: Provide 2 coats of

    finish over a primer.

    a.Prime Coat: Interior/Exterior Acrylic Rust-inhibitive Maintenance Primer.

    b.Finish Coat: Interior [Eggshell] [Semi-Gloss] [Gloss] Latex Enamel.5.Interior Waterborne Polyamide Epoxy System: Provide 2 coats of finish over a primer.

    a.Prime Coat: Interior/Exterior Acrylic Rust-inhibitive Maintenance Primer.

    b.Finish Coat: Waterborne Polyamide Epoxy Finish.

    E.Ferrous Metal (Dry-Fall Application).

    1.Interior Latex Dry Fall [Flat] [Semi-Gloss] System: Provide 1 coat of finish [over a rust-

    inhibitive primer].

    [a.Prime Coat: Interior/Exterior Acrylic Rust-inhibitive Maintenance Primer.]

    [a] [b].Finish Coat: Interior Latex Dry Fall [Flat] [Semi-Gloss].

    F.Galvanized Metal (Dry-Fall Application).

    1.Interior Latex Dry Fall [Flat] [Semi-Gloss] System: Provide 1 coat of finish [over a rust-

    inhibitive primer].

    [a. Prime Coat: Interior/Exterior Acrylic Rust-inhibitive Maintenance Primer.]

    [a] [b].Finish Coat: Interior Latex Dry Fall [Flat] [Semi-Gloss].

    G.Wood and Wood Trim – Stain and Clear Finish.

    1.Interior Stain/Water-Reducible Polyurethane [Satin] [Semi-Gloss] [Gloss] Finish System:

    Provide 2 coats of finish over a stain and sanding sealer.

    a.Stain Coat: Interior Hi-Solids Penetrating Stain.

    b.Sanding Sealer: Interior Water-Reducible Acrylic Sanding Sealer.

    c.Finish Coat: Interior Water-Reducible Polyurethane [Satin] [Semi-Gloss] [Gloss]

    Finish.

    H.Wood and Wood Trim – Opaque.

    1.Interior [Eggshell] [Semi-Gloss] [Gloss] Latex Enamel Finish System: Provide 2 coats of

    finish over a primer.

    a.Prime Coat: Interior Latex Enamel Undercoater.

    b.Finish Coat: Interior [Eggshell] [Semi-Gloss] [Gloss] Latex Enamel.

    Paints and Coatings

     09 91 23-10

Report this document

For any questions or suggestions please email
cust-service@docsford.com