DOC

Datasheet_US Plug (1-15P)

By Bryan Crawford,2014-03-11 16:15
16 views 0
Datasheet_US Plug (1-15P)

    Job No.: GZ10020303 Page No. Appendix page Test Date: Tested by: Sample No.: S10020303- Checked By:

Equipment’s combined with two-pole plug (Class II)

    Supplementary tests on plug portion are according to ANSI/UL 1310

    Requirement - Test Result-Remark (Equipment) Verdit

    1 Dimensions - 1.1 Checked according to NEMA WD 6-2002

    figure 1-15

    1.2 Checked according to figure 7.1, 7.5, sub-

    clauses 7.11, 7.16 of ANSI/UL 1310

    2 Direct Plug-In Blade Secureness Test - 2.1 Each blade subject to pull test (89N / 2 min) Displacement:

    and then two blade subject to pull test (89N /

    2min) together. The displacement of each

    blade shall not exceed 2.4 mm measured 2

    minute after remove the weight. (clause 43 of

    ANSI/UL 1310)

    3 Direct Plug-In Security of Input Contacts Test - 3.1 Push test of each blade (133N / 1 min); Blades are not loosen

    (clause 44.1.2 of ANSI/UL 1310)

    3.2 Then the same specimen subject to push test Blades are not loosen

    of all blades (178N / 1 min); (clause 44.1.3 of

    ANSI/UL 1310)

    The blades shall not loosen.

    3.3 Folding and retracting blades subject to 6000

    cycle rotating

    3.4 After test, it shall

    a) Be operational

    b) Not expose live part

    c) Not influence plug and unplug to

    receptacle

    d) Comply with test of clause 43, 44.1.2,

    44.1.3

    e) Not alter the temperature rise of blade

    contact under normal operation

Equipment used:

    Job No.: GZ10020303 Page No. Appendix page Test Date: Tested by: Sample No.: S10020303- Checked By:

Dimension Checking for Two-pin plugs of NA (15 A, 125 V)

     According to (NEMA WD 6-2002 Figure 1-15)

    Symbol Requirement (inch) Measured (inch) Symbol Requirement (inch) Measured (inch)

    A 0.120 - 0.130 E 0.240 - 0.260

    B 0.151- 0.161 F 0.307 - 0.322

    C 0.449 - 0.479 G 0.055 - 0.065

    D 0.625 - 0.718 H 0.495 - 0.505 Perimeter faces to the plug blades shall not be less than 7.9 mm (intended for use with children’s toys) or 5.1 mm from any point of either blade

Equipment used:

    Job No.: GZ10020303 Page No. Appendix page Test Date: Tested by: Sample No.: S10020303- Checked By:

Dimension Checking for Two-pin plugs of NA (15 A, 125 V)

     According to Figure 7.1 of ANSI/UL 1310

    Symbol Requirement Measured Symbol Requirement Measured W < 794 g g X ; mm

    Y ; mm WY/Z 1361 g g

    Z ; mm WY/S 1361 g g

    S ; mm WX 0.56 Nm Nm Note:

    1) W: the weight of the unit;

    2) Y: the distance illustrated in the figure above (mm);

    3) Z: the lesser of the two distances, Z1 or Z2, as illustrated in figure above (mm); 4) S: the lesser of the two distances, S1 or S2, as illustrated in figure above (mm); 5) X: the greater of the two distances, X1 or X2, as illustrated in figure above (mm).

Equipment used:

Report this document

For any questions or suggestions please email
cust-service@docsford.com